Cylinder head - Min Tec head range

I'm often asked about the range of cylinder heads I do for Mini Spares/Mini Mania, so here's the low-down…

Although the following range of heads accommodate specific fitments - like pre-1992 where by-pass hoses and heater take-offs on the clutch end of the head are used and post-1992 where neither of these exist, and on SPi (single point injection) heads where they don't usually have a threaded hole for the temperature sender - in reality it is easy to convert almost any of them to fit any other engine since holes are easily blocked off - or by-pass hoses not used, water pumps blanked off and drilled thermostats fitted (see articles on cooling/engine transplants). A list of which is what and what to do to each to convert is at the end of this article.

For more in-depth descriptions of the head specs, see article 'Cylinder head - About Min Tec Heads' - basically the valve sizes used have been decided on after extensive and in-depth flow test...

Engine - 998 tuning, further options

Following on from the easily bolted on performance enhancing components out-lined in the stage one section, we need to consider where to go to get more power output.

Terminology:
MSC/MM - Mini Spares Centre/Mini Mania
BBU - Big Bore Unit (refers to all 1275cc-based units)
SBU - Small Bore Unit (refers to all sub-1275cc units, here the 998)
BHP - Brake Horse Power
CR - Compression Ratio

To improve engine out-put, you need to increase the engine's 'breathing' ability. The stage one kit deals with all the easily bolted-on external parts, and represents the best increase for investment. From here on in the power increases will cost commensurately more money. Power production of any engine, once the 'breathing apparatus' (induction/exhaust system) has been dealt with to cause no restriction ...

Engine - 1275, 95bhp sports/tourer test result

DIY enthusiasts often believe that building an engine to give excellent all-round road performance is beyond them. Mainly from comparisons made between what they have been able to achieve and what specialists say should be achievable from any particular type of engine build.

Generally scrambled further by the non-perfect match of parts and components used between aforementioned specialist and erstwhile DIY-er, and the ritual 'nose-tapping and knowing winks' display of those specialists. Something you can very nearly 'see' even when talking to such folk on the phone - or that inimitable 'ah, yes, well…' So some form of 'black art' is implied. Whilst there is most definitely a degree of 'feel' involved between the real specialist's results and those of just a good engineer - the bones of the deal is subject to no such thing and is certainly within the capability of the DIY enthusiast given the necessary information. And that has been the problem.

Engine transplants - initial information and engine choices

Is this familiar? - You take the small one out; you put the big one in. In, out, in, out, shake your fist about, you do the hokey-cokey and you turn around, that’s what it’s all about...

Terminology -
BBU - Big Bore Unit
SBU - Small Bore Unit
Bodge - English term for 'make do' engineering- assured to fail at an in opportune
Moment.
Dizzy - Distributor

NOTE; this information is largely for transplanting large-bore units into small-bore engined cars.

Is this familiar? - You take the small one out; you put the big one in. In, out, in, out, shake your fist about, you do the hokey-cokey and you turn around, that’s what it’s all about...kinda sums up the situation many folk find themselves in when attempting to endow their beloved Min with a more impressive turn of speed.

C-AJJ4064 – 8 PORT CYLINDER HEAD

The combustion chambers are left in a basic shape only with a nominal 16.4cc which allows enough metal for those with the latest advanced ideas of shape to apply them and create the correct compression ratios for the desired use.

Valve and seat material specification allows use of unleaded fuel. Thoroughly clean the cylinder head before final assembly. Check that the small circlip is in the correct position in the valve guide at a point where the guide protrudes through the cylinder head beneath the valve seat. Place the valve spring seat over...

ARDEN 8 PORT ALLOY HEAD

Still produced from the original tooling purchased in 1990 from Jim Whitehouse these Arden alloy 8 port heads were never a straight bolt on conversion. Designed with racing in mind it was developed in 1966/7 to take full advantage of the change to Group 2 racing regulations which allowed more freedom in cylinder head design.

C-GRH240 C-GRH247 C-GRH1006 SILICONE HOSES

This hose has been designed to fit any pre 1989 Mini where the heater valve is bolted on the cylinder head. Later cars had an in-line valve and different plumbing.

C-GRH240 BOTTOM HOSE

1. This hose has been designed to fit...

05.06.10, Brands Hatch race report by Keith Calver

I am not sure why, but I don't really enjoy Brands Hatch. It is a quite technically difficult circuit to set fast lap times on. It is most definitely one of those circuits that 'be slow to go fast' applies to.

You can not hustle or hurry it. I am speaking from the point of view of having to use treaded tyres that don't give a tremendous amount of grip. And probably a circuit where 'loose is fast' applies... but I am still building confidence.

Cylinder head 2022

Historical Article - Nov 1991 - Twini Mini

The front brakes are standard Cooper 'S' 71/2" variety with the standard drums on the rear, with the assistance of a servo the rear regulator valve has been left out of the system and the brakes work very well. As the weight of the second engine amounts to the equivalent of two 11 1/2 stone passengers. Rear cooling is taken care of using a 1300 radiator mounted in the standard position. The heater take offs are connected to a 19 row oil cooler.

Historical Article - Nov 1991 - Twini Mini

The front brakes are standard Cooper 'S' 71/2" variety with the standard drums on the rear, with the assistance of a servo the rear regulator valve has been left out of the system and the brakes work very well. As the weight of the second engine amounts to the equivalent of two 11 1/2 stone passengers. Rear cooling is taken care of using a 1300 radiator mounted in the standard position. The heater take offs are connected to a 19 row oil cooler.